1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
  2. Welcome to the new DBSTalk community platform. We have recently migrated to a community platform called Xenfono and hope you will find this change to your liking. There are some differences, but for the most part, if you just post and read, that will all be the same. If you have questions, please post them in the Forum Support area. Thanks!

Remote help

Discussion in 'DIRECTV HD DVR/Receiver Discussion' started by bflora, Dec 11, 2013.

  1. bflora

    bflora Legend

    176
    5
    Nov 5, 2007
    I want to change a remote from audio "punch thru" back to where the volume and mute control the tv audio rather than a stereo receiver. The stereo was on av2 and I tried going through the setup on av2 and entering 993 and vol down, but this did not allow the remote to control the tv volume. I finally reprogrammed av2 to the same tv setting as the tv position of the slide switch. This accomplished the task but is there a more direct way to turn off/on the audio "punch thru"?
     
  2. b52pooh

    b52pooh Cool Member

    303
    18
    Mar 10, 2011
    Southern Oregon
    You could reset the remote to factory defaults, Mute/select, two flashes, then 981, you should see 4 flashes. But this would mean you have to reprogram the TV code again. Then the remote will control the TV volume by default. In addition, if you have the remote in RF mode for the IRD, you will need to reprogram that feature also.
     
  3. bflora

    bflora Legend

    176
    5
    Nov 5, 2007
    Thanks! I have another question. I have a RC65RX set to RF for my HR34 and AV1 set to IR DTV. I want to change AV1 to RF for an HR20. What is the process to do this?
     
  4. Edmund

    Edmund Remote Master

    1,781
    12
    Apr 17, 2003
    Southern Ca
    All you have to do is go to the tv device on the remote, punch it through to all devices again:

    1. tv
    2. press and hold MUTE & SELECT, wait for two blinks, release
    3. enter 9 9 3
    4. press SELECT

    Now tv volume is in all devices, to restore the av2 volume in just that device:

    1. av1 or av2
    2. press and hold MUTE & SELECT, wait for two blinks, release
    3. enter 9 9 3
    4. press VOL DOWN
     
  5. Edmund

    Edmund Remote Master

    1,781
    12
    Apr 17, 2003
    Southern Ca
    1. av1 or av2
    2. press and hold MUTE & SELECT, wait for two blinks, release
    3. enter 0 0 0 0 1
    4. press and hold MUTE & SELECT, wait for two blinks, release
    5. enter 9 6 1
    6. press CH UP
    7. enter last 6 digits of Receiver ID #(RID), found on a sticker in the access card compartment
    8. press SELECT
     
  6. Supramom2000

    Supramom2000 In Loving Memory of Onyx-2/23/09

    3,787
    159
    Jun 20, 2007
    Colbert, WA
    Edmund, do you know of any Proscan TV codes for an RC65R - that are not in the menu choices already? I think there were 6 or 7 of them and none of them worked. I tried all of them twice.

    Also, I have a spare RC71 (because I don't like it for my main usage) that I tried to match up to this Proscan with an old R22. However, I could not get it to even power the R22 at all. I did the reset of the remote with the mute + select 981, but although the lights blink appropriately, it won't control the DVR. Any tips?

    Thanks!
     

Share This Page