1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

HR34: Version 0x0582 Issues/Discussion

Discussion in 'DIRECTV HD DVR/Receiver Discussion' started by Stuart Sweet, Aug 23, 2012.

  1. Aug 26, 2012 #21 of 139
    jibberyerkibber

    jibberyerkibber Legend

    238
    6
    Mar 1, 2012
    I too have discovered that occasionally the HR34 won't go to a new channel I entered into the remote. Simply stays on the old channel.
     
  2. Aug 26, 2012 #22 of 139
    jibberyerkibber

    jibberyerkibber Legend

    238
    6
    Mar 1, 2012
    I'm watching a channel that's in Custom One, my normal FAVORITES list. Then I key into the remote a channel that's not in my favorites list. Fine. That channel appears. Then I press PREV to go back to the previous channel that is in the favorites list. Fine. The HR34 gos there. Then I press PREV again to go back the channel that's not in my favorites list. Not so fine. The HR34 goes to the top channel in my LAST FOUR list. The LAST FOUR list does not contain the non-favorites channel I keyed in. Seems like the LAST FOUR list and the PREV command don't like channels that are not in your favorites list.
     
  3. Aug 26, 2012 #23 of 139
    jibberyerkibber

    jibberyerkibber Legend

    238
    6
    Mar 1, 2012
    FFWD > PLAY > BACKSPACE several seconds to a place in the video before you pressed PLAY so as to compensate for your recognition/reaction time lag.

    It seems the 0x582 HR34 BACKSPACES now when I press PLAY when I'm in the FFWD mode. So far, cross my fingers, the 0x582 HR34 has done it every time. Most of the time the previous software did not BACKSPACE at all. But, at least for me, the 0x582 HR34 does not back space far enough. I still have to press the REPLAY button once or twice to get the video back to a point a few seconds before I pressed PLAY. My HR23 and HR24, as they always have, BACKSPACE properly, although often too far. I'd still rather go too far than not far enough.
     
  4. Aug 26, 2012 #24 of 139
    rbohling

    rbohling Cool Member

    11
    0
    Apr 20, 2012
    Bullard, TX
    My issue carried over from the previous update. My extras page was blank, after the previous software update and I had white triangles on certain channel tabs, within the guide.

    I got home from work today and there was a message from the DirecTV tech, saying there was a new update and to see if it corrected the problems. I checked and no extras, but white triangles are gone. Did two consecutive reboots...no extras. Did a red button reboot and a forced software download...no extras. :nono:
     
  5. Aug 26, 2012 #25 of 139
    RunnerFL

    RunnerFL Well-Known Member

    17,054
    312
    Jan 4, 2006
    The extras take time to repopulate if lost.
     
  6. Aug 26, 2012 #26 of 139
    Drucifer

    Drucifer Well-Known Member

    9,407
    244
    Feb 12, 2009
    NY Hudson...
    As I understand it, the Extra Icons are part of a followup download, which is supposed in occur within 24 of the software install..
     
  7. Aug 26, 2012 #27 of 139
    RunnerFL

    RunnerFL Well-Known Member

    17,054
    312
    Jan 4, 2006
    Correct, and that can't be triggered.
     
  8. Aug 26, 2012 #28 of 139
    rbohling

    rbohling Cool Member

    11
    0
    Apr 20, 2012
    Bullard, TX
    What time frame are we talking about? They disappeared when the previous software update occurred and never returned. This 0X582 update was Friday at 0105 and they were not there today Sunday afternoon 1500. Now that I cleared the cache (two reboots) and then a reboot, with software install, when should I realistically expect to see something?
     
  9. Aug 26, 2012 #29 of 139
    RunnerFL

    RunnerFL Well-Known Member

    17,054
    312
    Jan 4, 2006
    If they didn't download with the update it could take a while. They will only download when/if your DVR is not being used, not recording, not doing housekeeping, etc.

    When you re-downloaded did you see a prompt about allowing it to download "Additional Software"? If you did and told it to download later it could take quite a while.
     
  10. Aug 26, 2012 #30 of 139
    rbohling

    rbohling Cool Member

    11
    0
    Apr 20, 2012
    Bullard, TX
    No, there was nothing about "Additional Software". I saw some mention of that, when people were discussing issues with the previous version. I have never seen a prompt for that.
     
  11. Aug 26, 2012 #31 of 139
    chkinela

    chkinela New Member

    7
    0
    Jul 10, 2012
    You aren't by chance setup with IAMANEDGECUTTER menus are you? I didnt have the extras until I searched IAMANEDGECUTTER NOT and reboot. All the extra's loaded at that reboot. This new update so far has solved by HDMI handshake issues. Time will tell though.
     
  12. Aug 26, 2012 #32 of 139
    rbohling

    rbohling Cool Member

    11
    0
    Apr 20, 2012
    Bullard, TX
    I had it on there, but it was nothing I wanted and it has already been removed. It was gone a while back. Thanks
     
  13. Aug 27, 2012 #33 of 139
    iceman2a

    iceman2a Icon

    545
    0
    Dec 30, 2005
    Hudson, FL...
    I now have a few error msgs I never had:

    776 can not comunicate with dish!
    ALL channels working fine! all signal lvls are good, just a nagging error msg across the screen! Menu reset clrs it for a few hours but then it returns! "system test" finds no problems!

    Also got a "not enough swm chnls avlbl" msg once. This is the only rcvr off swm 2 output of swm16. Chkd the PI it looked ok, unplugged for a couple of mins, plugged it back in, clrd this msg???? :confused:
     
  14. Aug 27, 2012 #34 of 139
    Stuart Sweet

    Stuart Sweet The Shadow Knows!

    37,060
    287
    Jun 18, 2006
    iceman2a, both these errors have to do with the way the SWM is configured. It thinks there are more than 8 tuners on a SWM leg. Is it possible that the message is correct?
     
  15. Aug 27, 2012 #35 of 139
    gregftlaud

    gregftlaud Hall Of Fame

    1,093
    0
    Nov 20, 2005
    Power was off all nite/morning here in ft lauderdale b/c of the tropical storm.

    Restarted my PI, then bedroom HR21 works fine.....all signals good.

    But now i've got my HR34 started up......everything works just fine went to check signal strengths but the strength test/meter for the SWM is missing even though i went to system info and SWM is installed. Did a system test passed fine. SWM meter is showing on the HR21 ok not sure why I cant check my SWM readings on my HR34.

    Watching live tv, etc etc everything working fine i just dont have a signal test/meter included for the SWM on the view sat sig strength page. All others are there ie 101, 99's, 103's.

    Maybe a restart??
     
  16. Aug 27, 2012 #36 of 139
    iceman2a

    iceman2a Icon

    545
    0
    Dec 30, 2005
    Hudson, FL...
    6 tuners off swm 1 out, just the hr34 off swm 2 out! Have not had that error msg since I power cycled the PI. Don't really think this is related to software update, just all these happen since Friday!
     
  17. Aug 27, 2012 #37 of 139
    TJNash

    TJNash AllStar

    198
    11
    Jun 5, 2012
    San Diego
    I, too, have encountered this issue.
     
  18. Aug 27, 2012 #38 of 139
    chkinela

    chkinela New Member

    7
    0
    Jul 10, 2012
    So much for the HDMI fix...back to component for me. I had a HR21 hooked up for 4 years with not one HDMI drop and since the HR34 I have had to use component just for consistent picture and sound. I really hope they fix this soon.
     
  19. Aug 28, 2012 #39 of 139
    jcwest

    jcwest Legend

    324
    5
    May 3, 2006
    Got my HR34 on 8/18 and it loaded 057c software.

    The only problem I had initially was the unit kept dropping network connection and my other DVR's wouldn't see it in MRV mode.
    I switched the HR34 IP address to static and rebooted the other units and MRV has worked perfectly since.

    Running 57c my HR34 has worked flawlessly for a whole week, ha ha...

    Last night (running 0582 software) when I finished a recording and selected delete the box sat there for a couple of minutes before deleting the recording and when it finally deleted the PIG window was all black.
    After exiting out of the playlist there was no video output at all, the channel banner would show up when changing channels but no video, OTA and DTV channels.

    Any recording would output video and any channel that was recording would show live TV everything else black.

    Did a menu reboot and all returned to normal.

    J C
     
  20. Aug 28, 2012 #40 of 139
    acer505

    acer505 Cool Member

    37
    1
    Nov 14, 2007
    Did anyone get this problem after the update my HR34 only sees 4 tuners not 5.
     

Share This Page