DBSTalk Forum banner
1 - 7 of 7 Posts

·
New Member
Joined
·
2 Posts
Discussion Starter · #1 ·
** I did hours of research and due diligence before posting.


I have a DECABB1R0 (Black BB DECA) in my office next to my router. In my living room the coax plugs directly into my HR-24 with MRV. Yesterday I purchased a green-label SWM (splitter) so that I could send 1 line into the HR-24 and the second into another DECABB1R0 and then into a switch so I could plug in some other components.

All the setups I've seen use a DECA1MR01 (white) on the receiver side with a PI. Is my logic flawed that a DECA is a DECA. Black or white they do the same thing and rather than buying a DECA1MR01 with a PI I can just buy a second DECABB1R0 for the receiver/split side?

Thanks in advance and please forgive me if I messed up the terminology. I'm new to the whole satellite world (about 6 hours).
 

·
Godfather
Joined
·
322 Posts
the HR24 has a built in DECA and will disable it if the ethernet port is connected

so you shouldn't need a white deca

so you should be fine with using a DECABB to link the deca system to your network and won't need a white deca

the White deca with a PI as far as I can tell is just an improvised black deca
 

·
Super Moderator
Joined
·
42,754 Posts
TheGreek said:
** I did hours of research and due diligence before posting.

I have a DECABB1R0 (Black BB DECA) in my office next to my router. In my living room the coax plugs directly into my HR-24 with MRV. Yesterday I purchased a green-label SWM (splitter) so that I could send 1 line into the HR-24 and the second into another DECABB1R0 and then into a switch so I could plug in some other components.

All the setups I've seen use a DECA1MR01 (white) on the receiver side with a PI. Is my logic flawed that a DECA is a DECA. Black or white they do the same thing and rather than buying a DECA1MR01 with a PI I can just buy a second DECABB1R0 for the receiver/split side?

Thanks in advance and please forgive me if I messed up the terminology. I'm new to the whole satellite world (about 6 hours).
While using another DECA this way, isn't "supported" [by DirecTV] you shouldn't have a problem.
The black one comes with a PI, while the white ones are intended to be connected to the receivers that don't have a DECA internally, and get powered from the receiver. If you use a white DECA, there is a PI made for them, if not being powered by a receiver.
"DECA is DECA", until you find the wireless DECA.
 

·
New Member
Joined
·
2 Posts
Discussion Starter · #4 ·
Thank you both for your reply.

VeryOldSchool thank you for all your posts. Last night I read thread after thread in an attempt to understand my options and VeryOldSchool was in most of them. I appreciate your commitment to the community.


For the sake of people who may search this in the future let me repeat.

A Deca is a Deca....white or black they are the same. The black DECA's come with power where the white ones may need a PI if not powered by the receiver. The new HR-24's have built in DECA's. If you want to put a switch by your TV so you can plug devices into the internet you'll need to get a green label splitter (SWM). One wire from the splitter will go directly into your HR24 (then you're all set for TV). The second wire will go into your DECA device (white with PI or the Black Deca). From there you will have an ethernet cable to with as you would like.
 

·
1*
Joined
·
10,289 Posts
TheGreek said:
Thank you both for your reply.

VeryOldSchool thank you for all your posts. Last night I read thread after thread in an attempt to understand my options and VeryOldSchool was in most of them. I appreciate your commitment to the community.

For the sake of people who may search this in the future let me repeat.

A Deca is a Deca....white or black they are the same. The black DECA's come with power where the white ones may need a PI if not powered by the receiver. The new HR-24's have built in DECA's. If you want to put a switch by your TV so you can plug devices into the internet you'll need to get a green label splitter (SWM). One wire from the splitter will go directly into your HR24 (then you're all set for TV). The second wire will go into your DECA device (white with PI or the Black Deca). From there you will have an ethernet cable to with as you would like.
You got it perfectly. Just to reiterate though, hooking up your other components to use the DECA is not supported by DirecTV. If you have an issue with MRV or other aspects regarding connectivity of your receivers, be sure to disconnect that aspect of your network completely in order to troubleshoot and before you call DirecTV.

- Merg
 

·
Legend
Joined
·
264 Posts
Before this gets to far out of hand, 1) you do not need a spliter of any kind on the sat coax as that does not connect to the network directly. 2) If you connect a network switch on the either cable between the decca and the reciever, 90% of the time you will have problems with all the network devices that are connected to that switch.

Yes, it may work, but about the time you really wish you had the internet, it will crash.

This also holds true for the 610 wireless kit from DTV.

If you are going to connect other device to the internet that are in the same location as your reciever, then do one of two things.
1) try and run a either cable to that location then use a switch.
2) get a wireless router, configure for bride mode conneted to your main wireless router
leaving the network connection to your DTV reciever out of the picture.

The #1 connection type is the hard wire with wireless #2
again, leave the reciever alone.
 

·
Super Moderator
Joined
·
42,754 Posts
cabletech said:
Before this gets to far out of hand, 1) you do not need a spliter of any kind on the sat coax as that does not connect to the network directly. 2) If you connect a network switch on the either cable between the decca and the reciever, 90% of the time you will have problems with all the network devices that are connected to that switch.

Yes, it may work, but about the time you really wish you had the internet, it will crash.

This also holds true for the 610 wireless kit from DTV.

If you are going to connect other device to the internet that are in the same location as your reciever, then do one of two things.
1) try and run a either cable to that location then use a switch.
2) get a wireless router, configure for bride mode conneted to your main wireless router
leaving the network connection to your DTV reciever out of the picture.

The #1 connection type is the hard wire with wireless #2
again, leave the reciever alone.
And though "I thought I knew..." you've got me completely :confused:

The topic was DECA, which needs a coax, or needs to be fed off a splitter if the receiver has the only coax coming into the location. Only the Wireless CCK, doesn't require a splitter or a separate coax.
Wireless for MRV isn't a good idea, but for anything off the internet, shouldn't be a problem.

"I don't think" this has a 90% screwed up mode:
 
1 - 7 of 7 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top