DBSTalk Forum banner
1 - 4 of 4 Posts

·
Hall Of Fame
Joined
·
8,058 Posts
DarkLogix said:
ok I guess the 2nd coax was ether in error or for some other reason, I did have a fishy feeling about it

could they one day have a new sat in a new position that could use flex#2?

/last ot question
No the 95W "World Direct" dish in SD installations actually should have three lines. Two for a standard 12.2-12.7 Ghz 101 LNB and one for a 95W 11.7-12.2 Ghz linear LNB, both mounted at the focal point of the dish.

Its just that in HD installs when used in conjunction with a SlimLine 3/5 dish it is customary to not even bother running any lines for the 101 LNB since its not used.

EDIT: My bad, for a standard installation there actually should be "three" cables coming from a World Direct dish for an SD install as corrected above due to two cables for the 101 LNB.
 

·
Hall Of Fame
Joined
·
8,058 Posts
veryoldschool said:
We've got the winner here!

When/if more tuners get added:

Although for some strange reason, I read in a D* tech bulletin about the SWiM-16 awhile ago, the exact edition I can't remember at the moment. That cascading two of them this way was not yet recommended. :confused:

Never could figure out why, or if that advisory was ever since officially rescinded.
 

·
Hall Of Fame
Joined
·
8,058 Posts
BTW, happened to stumble across the particular "Technical Bulletin with points against cascading SWiM-16s highlighted. As to why is anyones guess.

Sorry for posting it to this thread somewhat belatedly :D

Issue 5 2011 - 4.25.11

SWiM 16
--------
· There is a DECA Bridge on the SWiM 16 for receiver call backs and Whole Home DVR communication pathways. IMPORTANT: There must be a receiver connected with an external or built-in DECA on both sides of the 2 separate SWiM 8's for the DECA bridge to facilitate cross communication, and an active phone line or broadband connection must be attached to one of the receivers for receiver call backs.

· The SWiM 16 is supplied signal by an SL3 or SL5 SLIMLINE LNB in the same way a 6x8 or SWiM multi-switch is provided signal.

· The SWiM 16 has two FLEX ports for the 95 (WORLDDIRECT) or 72.5 orbital slots.

· Utilize a power passing splitter if using more than one SWiM 16. Do not cascade the SWiM 16 due to high signal loss.

· Each SWiM output is an independent SWiM 8 and must be configured that way. For example: you can only use 8 tuners per SWiM output port so you can use 8 and 7 tuners but not 10 and 5 tuners as a configuration.

· The SWiM 16 uses the 29V SWiM power supply used with the SWiM 8 connected to SWiM port 1 for power.

· If you need to use 2 SWiM 16 Multi-Switches, power passing splitters should be used between the SLIMLINE LNB and the 2 SWiM 16 Multi-Switches. When using splitters, you need to make sure the same polarity is used from each splitter to the corresponding satellite in on the SWiM 16 Multi-Switch. For example: the same splitter must feed the 18V sat 99/101 sat in port.

· SWiM 16 is manufactured by ZINWELL.

· As with all SWiM installations, BBC's are never used, and all receivers must be SWiM capable.

· Use of the legacy ports for SWiM or non SWiM capable receivers on the SWiM 16 is not recommended at this time.

· The H25 receiver that will only work in a SWiM installation will work with the SWiM16
 

·
Hall Of Fame
Joined
·
8,058 Posts
DarkLogix said:
That sounds more like they're saying not to parallel SWM16's

it just sounds like they're using a parallel setup and saying cascade, because there would be no need for power passing splitters if cascased but there would be if paralleled
No it seems pretty clear they're saying quite the opposite;

Note the highlighted points again:

· Utilize a power passing splitter if using more than one SWiM 16. Do not cascade the SWiM 16 due to high signal loss.

· If you need to use 2 SWiM 16 Multi-Switches, power passing splitters should be used between the SLIMLINE LNB and the 2 SWiM 16 Multi-Switches. When using splitters, you need to make sure the same polarity is used from each splitter to the corresponding satellite in on the SWiM 16 Multi-Switch. For example: the same splitter must feed the 18V sat 99/101 sat in port.

· Use of the legacy ports for SWiM or non SWiM capable receivers on the SWiM 16 is not recommended at this time.

This clearly says that when two SWiM-16s are needed, paralleling is to be used and not cascading.

It appears when this TB was written for some reason they didn't (yet anyway) recommend use of the legacy ports due to a perceived "high (internal) signal loss" between the 4-6 satellite inputs and the legacy port outputs.
 
1 - 4 of 4 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top